Embedded WorksTrackingForLessSensorWorks

B+B SmartWorx WSD1CA3 WLS MESH ANALOG 3-AI SENSOR, INT ANT, CONDUIT - Lithium Battery (AA) / Grade: Industrial

WLS MESH ANALOG 3-AI SENSOR, INT ANT, CONDUIT

WSD1CA3

$449.00

MSRP $493.90 - Save $44.90 (9.09%)
Buy MoreSave More
10+$449.00
25+$449.00
100+Need volume? - Get Quote
WLS MESH ANALOG 3-AI SENSOR, INT ANT, CONDUIT

Wzzard™ Intelligent Edge Node With SmartMesh IP and Bluetooth LE
  • Ultra low power 802.15.4e SmartMesh IP technology
  • Communicates with Spectre Network Gateway via highly scalable and reliable wireless mesh networks
  • Connect to industry standard analog or digital sensors
  • Wzzard app lets you read or configure the nodes using Android or iOS tablets and smart phones
  • Rugged, IP67-rated, fiber reinforced polyester PBT enclosure
  • MQTT and JSON IoT protocol to application platform
Wireless Connectivity Where You Need It

The Wzzard™ intelligent wireless sensor platform creates a complete, quick and easy connectivity stack between your sensors and your application, on your network or on the Internet. The platform uses Intelligent Edge Nodes, a wireless 802.15.4e SmartMesh IP network to transmit sensor data to the Spectre Network Gateway. The Spectre Network Gateway can connect to the Internet via wired connections or the cellular data networks and communicate with application platforms using the MQTT IoT protocol and JSON data formats. The Wzzard Intelligent Edge Nodes nodes accommodate virtually any industrystandard external sensors. Connections can be made via conduit fitting, cable gland or an M12 connector. The Nodes provide a wide variety of sensor interface options, including general purpose analog inputs, digital input/output and thermocouple. They can also contain internal sensors like an accelerometer, depending upon the model number. All 802.15.4e Intelligent Edge Nodes contain an internal temperature sensor.
Power(2) 3.6V 2400 mAH Lithium Thionyl Chloride AA batteries
Battery LifeMultiyear based on 1 min sensor sampling and reporting
CertificationsCE
  • EN55022 CISPR (EN55022) Class A
  • EN61000-6-1 Generic Standards for Residential, Commercial, & Light Industrial
  • EN61000-6-2 Radiated immunity 10 V/m, 80-2700 MHz (EN61000-6-2) or Equivalent
  • EN61000-4-2 (ESD) +/- 15kV contact, +/- 4kV air
  • EN61000-4-3 (RFI)
  • EN61000-4-4 EFT
  • EN61000-4-5 Surge
  • EN61000-4-6 CI
  • EN61000-4-6 Power Frequency Magnetic
  • EN61000-4-11 Voltage Dips & Interruptions
  • EN60255-21-1 Vibration
  • EN60255-21-2 Shock


IEC
  • Shock and
  • Vibration
  • IEC 60068-2-27:2008 shock, 50g, 11ms half sine wave, 18 shocks
  • IEC 60068-2-6:2007 vibration, 2g, 10-500 Hz,1.5mm displacement


FCC
  • FCC Part 15 Class A
  • FCC - Part 15.247
  • Industry Canada - RSS210
  • CSA - Class 1, Div 2 Groups A, B, C, D (ANSI/UL equivalent)


REGULATORY APPROVALS
  • ROHS and WEEE Compliant
Maximum Operating Temperatures-40 to 80°C (-40 to 176°F)
Device Range
Device SpecificationsDIGITAL INPUTS
Voltage range: 0 - 48 VDC
VIL: 0.97 V Maximum
VIH: 1.8 V Minimum
Pull up current: 32uA
Type: Sourcing (PNP)/Sinking (NPN) Software selectable input
Isolation: None

RATE/FREQUENCY INPUTS

Frequency: Does a 1 second measurement at each measurement/publish interval
Can handle frequencies between 1 Hz - 1000 Hz
Uses the falling edge or rising edge based on the Invert Enabled setting

COUNTER INPUT
Channels: Actively counts either the falling edge (Invert enabled) or rising edge (Invert disabled)
Can use a multiplier to convert to a unit type or count
2 selectable/shared with Digital inputs
Rolls over at 999999.9

ANALOG INPUTS
Input ranges: 0 - 5 VDC, 0 - 20 mA
Resolution: 12 bit
Input load resistance: 100 Mega ohm (0-5VDC), 250 ohm (0 - 20 ma)

THERMOCOUPLE INPUT

Types Supported: J and K
Ranges Supported:
Type J -210 to +1,200 °C
Type K -270 to +1,372 °C
Resolution: 0.25 °C
Accuracy: Typical +/- 2 °C
+/- 6 °C over the temperature range of -40 to 80 °C

DIGITAL OUTPUTS
Voltage range: 0 - 30 VDC
Output Type: Open Drain
Output Current: Not to be less than 100ma
Protection: Current Limit Protection
Isolation: None

INTEGRATED SENSORS
TEMPERATURE
Conditions
Min
Typ
Max
Units
Offset:
Temperature Offset Error @ 25 °C

+/- 0.25

°C
Slope Error:


+/- 0.033

°C/ °C
3 AXIS ACCELEROMETER





Configurable measurement ranges:
+/-2 g, resolution of 1 mg/LSB
+/-4 g
+/-8 g




Configurable output data rates:
12.5Hz, 5Hz, 50Hz, 100Hz, 200Hz, 400Hz





SMARTMESH IP 802.15.4E RADIO SPECIFICATIONS
PARAMETER
Conditions
Min
Typ
Max
Units
Frequency Band:

2.4000

2,4835
Ghz
Number Of Channels:


15


Channel Separation:


5

Mhz
Channel Clear Frequency:
Where k = 11 to 25, as defined by IEEE 802.4.15

2405 + 5*(k-11)

MHz
Modulation:
IEEE 802.15.4 Direct Sequence Spread Spectrum (DSSS)




Raw data rate:


250

kbps
Range:
25 °C, 50% RH, +2dBi Omni-Directional Antenna, Antenna 2 m above ground
Indoor
Outdoor


100
300


m
m
Receiver Sensitivity:
Packet Data Error Rate (PER) = 1%


-93
dBm
Receiver Sensitivity:
BT SPEC.

-95
dBm
Output Power
Delivered to a 50 ? load




High Calibration Setting:



8
dBm
Low Calibration Setting:



0
dBm

BLUETOOTH LE RADIO SPECIFICATIONS
NO.
CHARACTERISTICS
CONDITIONS
MIN
TYP
MAX
BT SPEC.
UNIT
1
Operation Frequency Range:

2402

2480

MHz
2
Channel Spacing:


2


MHz
3
Output Power:
Maximum setting, measured at single ended 50ohm.
Minimum setting, measured at single ended 50ohm.

4
-24


dBm
dBm
4
Sensitivity, High Gain Mode:
High Gain Mode
Standard Mode

-93.0
-92.5

-70
-70
dBm
dBm
Dimensions3.75" x 3.81" x 2.57"
Applications
Enclosure MaterialIP67-rated, fiber reinforced polyester PBT
Operating Frequency
Packing List
Search in Results:
clear
  • Show
  • Per Page